Address

Culbertson Company 

7000 Tech Circle

 Manassas,Virginia 20109

Contact

(703) 369-2550 Phone

(571) 208-1630 Fax

©2017 by CULBERTSON COMPANY OF VIRGINIA LLC.

Tricks of The Trade

October 1, 2019

 

 

 

Know the purpose of each tool in your toolbox, and use each for the task it was designed to do. Keep cutting edges sharp. Before you lift anything think about the weight of the load. Too heavy? Get help, not hurt! When you do lift, bend your knees, hold the load close to your body and use your legs to lift. Be alert to eye hazards at your work site. Wear appropriate eye protection. On and off the job, protect your hearing by wearing the proper protection.

 

When working on straight ladders, use the four-to-one rule: position the ladder base one foot away from the wall for every four feet of ladder height. NEVER use the top two ladder rungs. ALWAYS observe no smoking signs -- they are there for your protection.

 

Lockout/tagout ensures that power sources have been temporarily turned off. You and ONLY YOU are responsible for removing your tag and lock when the job or repair is completed. ALWAYS wear your seat belt, it will save your life. Good housekeeping is a must. Clean up daily at the end of your shift. Plug power tools into grounded outlets that have ground fault circuit interrupters. Be sure that all electrical tools and extension cords are inspected and color coded quarterly. Before plugging or unplugging tools make sure the switch is in the off position. Watch out for pinch points! Do not remove guards or barriers.

 

ALWAYS wear personal protective equipment. Damaged or worn gear should be replaced at once. If you or someone you know suffers from heat exhaustion or cramps or heat stroke, get medical attention immediately. No horseplay on the job -- it's one of the primary causes of accidents. ALWAYS read a Material Safety Data Sheet before you begin a job using a chemical. Post emergency phone numbers near each job phone. Every second counts in the event of an accident or other emergency.

 

SAFETY STARTS WITH YOU! IF YOU FOLLOW THE RULES YOU SHOULD BE ACCIDENT FREE

SAVE YOUR BACK WHEN WORKING

IN AWKWARD POSITIONS

 

We have all been told to avoid back injury by bending our knees when we lift, keeping the load close and avoiding twisting motions. These safety rules may be appropriate for simple, direct lifting of materials, but what about back care when you are working in awkward positions? Work tasks that require you to reach or stretch away from your body while handling materials can also put excessive strain on the vertebral discs and soft tissues in the back. An awkward position is a work posture that distorts the spine from its natural curves, puts unbalanced pressure on the discs, and can strain arm, leg or back tissues if held for any length of time.

What are some work situations that may put you in "awkward" positions?

1. Jobs that require you to bend and reach into bins or containers to retrieve or place material.

2. Overhead work, installing or servicing equipment, pulling wire, cleaning ceilings, etc.

3. Floor or ground level jobs such as installing or servicing equipment, cleaning, etc.

4. Work tasks in confined or small spaces where there is limited range of motion such as boilers, hatches, pipes, tanks, vaults, crawl spaces, etc.

5. Jobs on ladders, work platforms or scaffolding where you may over-reach to adjust, clean, install or service.

6. Pulling loads, instead of pushing them, when removing equipment or other materials.

Repetitive tasks that require twisting of the back such as loading or handling material 90o to 180o from the starting point

 

How can you avoid injury when working in awkward positions?

 

  • Raise bins and containers off the floor and/or tilt them to reduce bending and over-reaching.

  • When working overhead, stand on a steady and adjustable platform. Keep your back posture in its natural curve to avoid uneven spinal loading.

  • If working on the floor, avoid bending over to work. Squat down using your leg muscles and wear cushioned knee pads if you have to kneel at work.

  •  In confined spaces, plan yo

     

    ur work, and reduce clutter in the area which confines you further and increases the need to twist or overreach. Also arrange for adequate illumination.

  • Don't hold an awkward position for too long. Pause often to stretch and straighten out.

  • When leaning forward to work, support the weight of your upper body on your free hand and arm, whenever possible. This greatly relieves pressure on your lower back.

  • Position yourself as close as possible to the job, avoid overreaching and/or use tools with longer handles when working on ladders or scaffolding.

  •  Never lift heavy loads that are far from your body's center of gravity. Get help in such cases.

  • Position your work below the shoulder and above the knees to minimize over-reaching.

  •  Push, rather than pull, loads to help maintain the spine's natural curve.

  • Remember that a back support belt may remind you to lift correctly, but it will not protect your spine if you overreach or twist with a load.

  • What specific awkward positions do you face in your work?

  • How can you "work smarter instead of harder" to prevent injuries?

 

Please reload

Our Recent Posts

Tricks of The Trade

October 1, 2019

Ladder Safety

September 3, 2019

The Fatal Four Hazards

August 1, 2019

1/1
Please reload

Tags

I'm busy working on my blog posts. Watch this space!

Please reload